Find the spare part you need instantly with quick, easy and AI-powered OEM code search. Enter your vehicle details and choose the right part!
An ABS sensor ring is a steel ring press-fitted onto the wheel hub or brake drum of a heavy commercial vehicle, with 80, 90 or 100 evenly spaced holes or teeth around its circumference. Although the name may suggest the clip or bushing that holds the ABS sensor, the products in this category are the toothed ring that the sensor reads, not the sensor itself or its retaining clip. In the field it is also known as a tone ring, exciter ring, pole wheel or ABS reluctor ring.
The ring rotates with the wheel. The stationary wheel speed sensor opposite it reads the passage of the holes and the solid sections between them and reports that wheel's speed to the ABS and EBS control unit.
The inductive wheel speed sensor common on heavy commercial vehicles has a magnet and a coil at its tip. As the ring turns, holes and solid sections pass in front of the sensor in turn; the magnetic field changes with each transition and an alternating voltage is generated in the sensor. The control unit divides the frequency of this signal by the tooth count it is set for, calculates the wheel's rotational speed and compares all wheels with one another.
The four basic dimensions that define a ring are inner diameter, outer diameter, height and number of holes. The table below shows the actual range of rings with recorded dimensions in VADEN products. On some products a dimension is given as two values (for example 153/172 mm); on stepped rings these indicate two measuring points. For selection, the dimensions on the product card and the OEM number are decisive.
| Feature | In VADEN products | Notes |
|---|---|---|
| Inner diameter | 102 – 180 mm | Determined by the seating diameter on the hub or drum |
| Outer diameter | 130 – 212 mm | Outermost circumference of the ring; used to check installation clearance |
| Height | 3 – 80 mm | Most products are 3 – 22 mm; there is a single tall-bodied type reaching 80 mm |
| Number of holes / teeth | 80, 90, 100 | Must match the control unit setting |
The category contains 38 products. Rings are mainly distinguished by number of holes, where they are seated and the axle they are used on.
Two rings that look alike can have a different number of holes or an inner diameter a few millimetres apart. Follow this order when selecting:
In every case, verify fitment by the OEM number.
Because the ring is a press fit, the quality of installation directly determines signal quality. The general steps are as follows; for heating temperature, pressing method and related settings, the vehicle manufacturer's current service manual applies.
The common symptom of ABS ring faults is the ABS warning lamp coming on. The lamp usually does not light while the vehicle is stationary, but when a certain speed is reached or within a certain speed range. The fault memory typically contains an incorrect, intermittent or erratic speed signal entry for the affected wheel.
Check the sensor, cable and connector first. If the fault returns even after the sensor has been replaced, the ring and wheel bearing play must be inspected.
The sensor clip (sensor bushing) is a small spring-loaded retainer that holds the ABS sensor in its bore on the axle and is a separate part, renewed with every sensor replacement. The ABS sensor ring, by contrast, is the toothed ring that rotates on the hub or drum.
VADEN ORIGINAL ABS sensor rings are supplied with dimension and hole count information matched by OEM number.
What is an ABS sensor ring, and is it the same part as the ABS sensor?
No. An ABS sensor ring is a steel ring seated on the wheel hub or brake drum with 80, 90 or 100 holes or teeth around its circumference. The ABS sensor is a separate electrical part that sits opposite the ring and reads the passage of those holes.
What are the symptoms of a faulty ABS sensor ring?
The most common symptom is the ABS warning lamp coming on, often only when the vehicle reaches a certain speed or within a certain speed range. The fault memory shows an incorrect, intermittent or erratic speed signal for the affected wheel.
How do I find out how many holes my ABS sensor ring has?
The most reliable way is the OEM number of the removed part. If the number cannot be read, put a chalk mark on the ring as a starting point and count the holes one by one. Rings with 80, 90 and 100 holes are common on heavy commercial vehicles; the new ring must have the same number of holes as the old one.
What happens if a ring with a different number of holes is fitted?
The ABS control unit calculates wheel speed from the signal frequency, based on the tooth count it is set for. A ring with a different number of holes makes that wheel appear to turn faster or slower than it really does. The result is a fault code, the ABS lamp and incorrect ABS intervention.
How is an ABS sensor ring installed?
Remove the old ring and clean the seating surface on the hub or drum completely of rust and burrs. Seat the new ring with even force around its circumference, using a suitable press tool or the heating method described in the service manual. Striking it with a hammer at a single point makes the ring oval. For heating and pressing values, the vehicle manufacturer's current service manual applies.
Can an ABS ring be cleaned and reused?
If the rust and dirt between the teeth are only superficial and the ring has no cracks, broken teeth, dents or runout, it can be cleaned and reused. A ring with thinned, broken or cracked teeth, or teeth lifted by rust, should be replaced.
Why does the ABS ring rust, and when does it become a problem?
The ring works inside the wheel, exposed to water, salt and brake dust. When rust fills the gaps between the teeth or lifts the tooth surface, the transitions the sensor sees become blurred and the signal weakens. On vehicles running on salted roads in winter, the ring should be checked more often.
Do trailer axles also have ABS sensor rings?
Yes. Axles of ABS-equipped trailers and semi-trailers also use a ring; axle manufacturers such as BPW, SAF and Gigant have their own rings with OEM numbers. Selection is again made by the axle manufacturer's OEM number.
Vehicle and engine pages that list parts from this category: Volvo D10 · Volvo D11 · Volvo D12 · Mack
Related technical guide: ABS Wheel Speed Sensor & ECU: Faults, Replacement & Care
Related products — Brake System: Sensor Holder · ABS Sensor (view all)
Main technical guide: ABS Brake System: How It Works, Warning Light and Faults
All products in this category (7): 9300 01 009 · 1100 03 013 · 1500 03 004 · 1200 03 001 · 1700 03 001 · 1400 03 005 · 9300 01 002