What Is an EGR Valve Repair Kit?

An EGR valve repair kit is a service set for renewing the internal parts that wear out over time in the valve of an exhaust gas recirculation (EGR) system. The EGR valve sends part of the exhaust gas back to the intake side, which lowers combustion temperature and NOx emissions. Because it is in constant contact with hot, sooty gas, the sealing elements and moving parts are the first to wear. The EGR valve repair kit covers these worn parts, so the valve can seal and work efficiently again without being replaced as a whole. Check the product page for the exact parts list.

When Is It Needed? Signs of Failure
  • Loss of Engine Power: With worn internal parts the valve cannot open and close fully; the air-fuel balance is upset and the engine pulls weaker.
  • Higher Emission Readings: A leaking or sticking valve cannot control the exhaust gas return rate; NOx and soot readings rise.
  • Warning Light and Fault Code: On electronically controlled systems the engine warning light comes on when the valve position deviates from the expected value; check it with a diagnostic tool.
Repair Kit or Complete Replacement?

The decision depends on the condition of the valve body. If the body is sound, renewing the internal parts lowers parts cost; if the body is damaged, a repair kit is not a lasting fix.

  • Repair Kit: Suitable when the valve body is sound and the problem comes from wear in the sealing elements and moving internal parts.
  • Complete EGR Valve: Preferred when the body is cracked, deformed or heavily corroded; in that case see the EGR Valve category.
Installation and Points to Watch
  • Clean the Body and Passages: Do not fit new parts until the valve body, seating surfaces and gas passages have been cleared of carbon deposits.
  • Do Not Reuse Old Gaskets: Hardened gaskets and seals should be replaced with new ones, and the sealing elements seated in the correct direction.
  • Tighten Connections Correctly: Bolts should be tightened in a cross pattern to the torque values specified by the manufacturer. Torque and adjustment values vary by engine; the vehicle manufacturer's current service manual is authoritative.
  • Test After Installation: Run the engine and check for leaks; on electronically controlled systems clear the fault codes and verify valve operation with a diagnostic tool.
VADEN ORIGINAL EGR Valve Repair Kit

This category includes the 0102 332 EGR Valve Repair Kit, made for MAN heavy-duty engines. The product can be fitted in place of MAN OE numbers 51.08150-6197 S, 51.08150-6199 S and 51.08150-6216 S.

Related technical guide: EGR Valve & EGR Flap: Faults, Replacement and Maintenance

Frequently Asked Questions (FAQ)
What is an EGR valve repair kit used for?

An EGR valve repair kit is a service set that renews the worn sealing elements and moving internal parts of the valve, so it can go back into service without replacing the whole EGR valve.

Should I buy a repair kit or a complete EGR valve?

If the valve body is sound and the problem comes from wear in the internal parts, a repair kit is the economical solution; if the body is cracked, deformed or heavily corroded, the complete EGR valve should be replaced.

What are the signs that an EGR valve needs repair?

A drop in engine power, higher emission readings, exhaust gas leakage, rough idle and the engine warning light coming on all indicate that the EGR system should be checked.

Which OE numbers does VADEN 0102 332 replace?

VADEN 0102 332 can be fitted in place of MAN OE numbers 51.08150-6197 S, 51.08150-6199 S and 51.08150-6216 S.

What should be watched during installation?

The valve body and passages should be cleaned of carbon, the new parts positioned correctly and the bolts tightened to the values specified by the manufacturer; the vehicle manufacturer's current service manual is authoritative.

Parent category: EGR Valves

Related products — EGR Valves: EGR Valve · EGR Valve Gasket · Engine (view all)

Works with: Exhaust System

Top Scroller